NaturoPure™ Air Purifiers

features

---

• Air Ionizer
  to energize the air with health beneficial negative ions.
• HEPA AIR FILTER
  Which is 99.97% effective at removing particles such as dust, pet dander & allergens.
• GERMICIDAL UV LAMP
  To destroy micro-organisms like germs, viruses, bacteria & mould.
• ACTIVATED CARBON FILTER
  For chemicals, gases, VOCs and cigarette smoke.
• TiO2 Photocatalytic Oxidation Board
  Activated by UV light, it relaease free radicals that destroy organic based pollutants.

PRE-OPERATING INSTRUCTIONS

---

• Carefully remove your air purifier from the gift box and the bag..
• Remove the black cover and remove the filter from bag.
• Select a firm level and flat location. For purpose air flow, locate the unit at least 1 foot(0.3) from any wall or furniture. Ensure no grilles are blocked.
• Plug the power cord into 220V AC outlet.

OPERATING INSTRUCTIONS

---

The air purifier is operated by the manual control located on the top of the air purifier (as shown in Unit top view)

1. Plug the air purifier into a 110V AC outlet.
2. Turn the air purifier on by pressing On/Off Button.
3. Upon turning the air purifier on, the power indicator will be lit, the unit will be in the High fan speed (3), and the ionizer will start to work.
4. Pressing Fan Speed Button at this point will set the air purifier into Medium fan speed (2).
5. Pressing Fan Speed Button again will set the air purifier into Low fan speed (1).
6. Pressing fan speed button once more will set the air purifier back to High fan speed (3).
7. To turn the air purifier off, press the On/Off Button

UV LAMP FUNCTION

The UV-C germicidal lamp can kill harmful airborne bacteria and virus. This function will work in any mode. Press the UV Button () to start the UV lamp and stop the UV lamp by pressing the UV Button again.

UV LAMP RESET FUNCTION

If the UV lamp needs to be replaced, the UV icon on the LCD will illuminate and flicker. After replacing the UV lamp, reset the UV lamp by pressing the UV Button for a few seconds, the UV icon will stop flickering and the new UV lamp will start to work. Check from the UV view window, if the UV lamp still lights, it should not be replaced.

HEPA RESET FUNCTION

If the HEPA filter needs to be cleaned, HEPA Reset icon on LCD will illuminate and flicker. After cleaning the HEPA filter, RESET the HEPA filter by using a pin or needle to press the HEPA RESET Button (), then the icon will stop flickering. For instructions on how to clean the HEPA filter see the CLEANING HEPA FILTER on page 7,8.

CLEANING AND MAINTENANCE

---

CLEANING PRE-FILTER (See Air Cleaning System)

1. Turn off unplug the unit.
2. Press the lock & Release Button and remove the Rear cover from the unit.
3. Remove the pre-filter from the rear cover. Clean the pre-filter with the vacuum brush attachment of your vacuum cleaner. This will remove lint and dirt from the filter. Use a clean, damp, soft cloth to wipe the pre-filter again.
4. After cleaning, reattach the pre-filter to the rear cover, and install the rear cover back to unit and securely latch in place.

SAFETY PRECAUTIONS

---

Ensure that all safety precautions are followed when using electrical appliances for the proper operation of the device.

This instruction booklet describes the safety precautions to be observed during operation to prevent injuries to yourself, other persons and damage to the device. The content not only is suitable for this product but also suitable for electrical appliances in general.

SPECIFICATIONS

---

• Air Ionizer
  to energize the air with health beneficial negative ions.
• Model:
  HF 290
• Power Supply:
  220V 50~60Hz
• Noise Level:
  ≤ 61dB
• Remove pollutants:
  Up to 0.03 micron
• CADR:
  110 CFM
• Power:
  55W
• Dimensions (L x W x H):
  25.5 x 17 x 55 cm (10” x 7” x 22”)
• Weight:
  4.14 kg (9.13 lb.)
• Applicable Area:
  It covers 270 sq. ft.